Compx-elock Network Cabinet Manuel d'utilisateur télécharger pdf (Page 6)

200/300 Series — CompX cabinet eLock Instructions

Unit Features:

w Choose 802.11g or Ethernet Networked configurations that

uses the facilities existing infrastructure for actual 2-way

read/write communication

w Each eLock can hold any combination of up to 3,000

Supervisors and Users

w Choose a model to use existing HID Prox, HID iCLASS, or

magstripe card credentials that can be programmed to

operate each eLock

w Remote Notification System with programmable escalating

alerts via SMTP email; SMS text, voice and fax (Networked

eLock & LockView Software required)

w Spring bolt latching mechanism provides automatic

relocking

w Optional second latch drive output (requires additional

hardware)

w Door position switch input (requires additional hardware)

w Membrane keypads with stainless steel domes provides

durable performance and easy cleaning

What’s in the box?

w 1 – eLock controller

w1 – motorized latch w/latch cable

w1 – battery compartment

w1 – battery cable

w2 –

10 x ½" philips pan head hi-low blunt point (type B)

SEMS mounting screw (used to mount eLock controller on

sheet metal application)

w2 –

10 x 1

" philips pan head hi-low blunt point (type B)

SEMS mounting screw (used to mount eLock controller on

MINIMUM

" thick application)

w2 –

8 x

" philips pan head wood screw for mounting battery

compartment

w4 –

10 x 1½" philips pan head wood screw for mounting

motorized latch

w1 – warranty card

w1 – serial code sticker set

w1 – in-box instructions

What’s needed?

w 6 – AA alkaline batteries

w Drill

2 philips head bit

w ½" drill bit for through hole battery cable

" drill bit for through hole Wi-Fi antenna cable

(300 Series Wi-Fi only)

" drill bit for through holes to mount eLock display unit

w T15 pin-in Torx (6-lobe) bit or driver

Care and Cleaning

The eLock is a battery operated device, therefore, it should

be part of a regular battery maintenance program.

Warning: install the batteries as shown in the battery

compartment. Polarity (+) or (-) must be correct. Replace

batteries as a set. Always use new batteries when replacing

the old set. Do not combine a used battery with a new one.

Only use alkaline batteries; do not mix battery types.

To clean the surface of the eLock, apply non-acid based

cleaner to a clean cotton cloth; do not spray cleaner directly

on the eLock. Wipe down keypad and housing taking care

around the beeper opening and edges of keypads. Wipe

excess cleaner off of all surfaces.

Setting up the eLock

Getting Started Out of the Box

If the eLock is stand-alone 200 Series (direct connection

via USB to LockView Software v4) and will be used in

conjunction with CompX’s LockView Software v4, please

follow the LockView Mode Instructions below.

For Networked (802.11g or Ethernet) 300 Series eLocks,

please follow the CompX eLock Database & Network

Conﬁguration & Install Manual and the CompX LockView

Software Instruction Manual before proceeding.

The eLock is shipped in FACTORY mode.

CONNECTING THE COMPONENTS:

1. Attach one end of the battery cable to the connector on the

back of the eLock controller.

2. Attach the other end of the cable to the battery

compartment.

3. Attach latch cable terminal to Latch 1 connector. (See

diagram for connector locations.)

4. Install 6 AA alkaline batteries. (not included)

200/300 Series Cabinet eLock — Instructions

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Compx-elock Network Cabinet Manuel d'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Compx-elock Network Cabinet