Compx-elock Network Cabinet Manuel d'utilisateur télécharger pdf (Page 7)

200/300 Series — CompX cabinet eLock Instructions

INITIAL PROGRAMMING:

1. The first time the eLock is powered up, FACTORY will be

displayed in the upper left hand corner of the LCD.

2. Press “MENU.”

3. Highlight CREDENTIAL MENU and press “NEXT/SELECT.”

4. Highlight ADD CREDENTIAL and press “NEXT/SELECT.”

5. CREDENTIAL TO ADD will be displayed.

When in FACTORY mode, the default status level for the first

credential is Supervisor, as Supervisor status is required to

allow access to further manual programming features.

There are two status levels; Supervisor and User. Only

Supervisors are, among other things, allowed to ADD,

DELETE, VIEW or EDIT Users and other Supervisors.

6. Scan first supervisor’s card credential (if equipped) or enter

first supervisor’s 4-14 digit PIN and press “ENTER.”

The Supervisor will be added to slot number 1.

7. To change the slot number, press “UP” to highlight and then

+ / - to move to next available slot; or use the numeric

keypad to enter the desired slot number

Press “NEXT/SELECT” when done.

8. CREDENTIAL NAME ENTRY will appear.

Press 2 - 9 for A - Z; press 1 for - , . , + or _ ; press 0 for

“space”; press and hold 0 - 9 for numbers (the maximum

number of allowed characters is 14).

9. Press “ENTER” when done. STORED will be displayed when

complete.

Using the various eLock LCD menu options, manual

programming can continue.

See CompX eLock Manual Programming Guide for complete

options and instructions.

10. Press BACK/CANCEL to exit.

Operating the eLock

Follow the instructions below to operate the eLock.

PIN CREDENTIAL

1. Enter a valid PIN (between 4 - 14 digits) and

2. Press “ENTER.”

CARD CREDENTIAL

If the eLock is equipped with a card reader (HID Prox, HID

iCLASS or a Magstripe)

1. Present a valid card within range of the HID reader or slide

the magstripe card through the magstripe reader.

DUAL CREDENTIAL

If the User or Supervisor requires a dual credential

1. Enter a valid PIN and press “ENTER” (for keypad credentials)

or present a valid card (for HID Prox or HID iCLASS or

Magstripe credentials).

2. Enter the second credential (4-14 digit PIN) and press

“ENTER.”

NOTE: THE SECOND CREDENTIAL MUST ALWAYS BE

A 4 - 14 DIGIT PIN

Methods to begin building

a database of eLocks in

CompX’s LockView Software

Note: Supervisor, User and parameter changes that already

exist in the eLock will automatically be carried into

LockView once the eLock has been enrolled.

For Networked (802.11g or Ethernet) eLocks, please

follow the CompX eLock Database & Network Conﬁguration

& Install Manual and the CompX LockView Software

Instruction Manual before proceeding.

LockView Mode Instructions

(For complete details on how to build a database of users

and eLocks, see the CompX LockView Software Instruction

Manual and CompX eLock Manual Programming Guide)

CompX LockView Software v4 must be installed and the

eLock must be in SETUP mode before continuing.

Stand-alone eLocks (Direct USB connection to laptop

computer with LockView is required) There are two methods

that can be used to add eLocks to the LockView software.

Automatic Method

1. With the eLock in SETUP mode, connect the eLock via the

USB cable to the computer on which LockView is installed.

2. Login to LockView.

200/300 Series Cabinet eLock — Instructions continued

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Compx-elock Network Cabinet Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Compx-elock Network Cabinet