Compx-elock Numeric Keypad Quick Programming Guide Manuel d'utilisateur télécharger pdf

1

CompX eLock

®

is a highly engineered lock with a motor-driven latch. Its uncompromising lock

control electronics include a non-volatile memory that stores 250 user / supervisor codes and

audit trail. With optional LockView

®

audit trail software, CompX eLock

®

remembers 1500 access

attempts. Programming is simple with numeric keypad or Windows

TM

based LockView

®

software.

Quick Programming Guide

1. GETTING STARTED:

a. The unit is shipped with no user / supervisor codes

b. Press and hold until the beeping stops

c. Input the new PIN (4 digit min) and press or present new card

d. This PIN / Card is now a supervisor in slot #001

2. ADD A USER:

a. Input a valid supervisor PIN and press or present valid supervisor card

b. Press and hold until beeping stops

c. Input the new user PIN (4 digit min) and press or present new card

3. ADD A SUPERVISOR:

a. Input a valid supervisor PIN and press or present valid supervisor card

b. Press and hold until beeping stops

c. Press and hold again until beeping stops

d. Input new supervisor PIN (4 digit min) and press or present NEW supervisor card

4. DELETE A USER OR SUPERVISOR:

a. Input a valid supervisor PIN and press or present valid supervisor card

b. Press and hold until beeping stops

c. Input the PIN to be deleted and press or present existing card to be deleted

5. ADD A USER WITH A SPECIFIC SLOT ASSIGNMENT:

a. Input a valid supervisor PIN and press or present valid supervisor card

b. Press and hold until beeping stops

c. Enter slot number that will be assigned to user and press

(example: to program slot 6 type 006 )

d. Input the new user PIN (4 digit min) and press or present NEW card

6. DELETE A USER WITH A SPECIFIC SLOT ASSIGNMENT:

a. Input a valid supervisor PIN and press or present valid supervisor card

b. Press and hold until beeping stops

c. Enter slot number to be cleared and press (example: to clear slot 6 type 006 )

d. Enter slot number to be cleared again and press (example: to clear slot 6 type 006 )

See programming

guide included

with optional

LockView

®

software for

advanced

programming

instructions.

NUMERIC

KEYPAD

MAGSTRIPE

CARD

PROX

READER

PROX READER / KEYPAD

DUAL SYSTEM

MAGSTRIPE / KEYPAD

DUAL SYSTEM

Thank you for choosing eLock.

1

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Thank you for choosing eLock

1CompX eLock® is a highly engineered lock with a motor-driven latch. Its uncompromising lock control electronics include a non-volatile memory that st

Page 2 - Accessories

2CompX eLock® AccessoriesHID is a trademark of HID Corporation. * These items are offered as Service / Replacement Parts only.AC ADAPTERPart Numbers:

Page 3 - TEMPLaTE on

3TEMPLaTE on oPPoSiTE PagE

Page 4 - Surface Mounting

41.817.77 NoTe:Don't forget to fill out and return yourwarraNTy card!CompX eLock® Surface MountingUse the diagrams below as a template for hole

Page 5 - Latch Dimensions

5warNiNg: Print this page and measure the line above. It is ONE INCH LONG. If it measures less than or more than one inch, the template measurements a

Page 6

6TEMPLaTE on oPPoSiTE PagE

Page 7 - Warranty Card

72d bar code. Provides the same information as sticker number three, but a 2d laser scanner is needed to decode the information.1d bar code. Place thi

Page 8

8sampleCopyright © 2009 CompX Security ProductsPart #: [email protected] Box 200Mauldin, SC 29662CompX eLock®

Modèles reliés Magstripe Card Quick Programming Guide | Magstripe / Keypad Dual System Quick Programming Guide | Prox Reader Quick Programming Guide | Prox Reader / Keypad Dual System Quick Programming Guide |

Commentaires sur ces manuels

Pas de commentaire